Happymodel 2.4g ExpressLRS ELRS Nano TX module ES24TX Slim for X-lite Tango2

Description

iFlight GOCam PM G3 GR 4K Camera 155FOV 2-6S for RC FPV Cinewhoop Ducted Drones
206.24 USD
224.17 USD
Free shipping
8%
off
IFlight FPV Drone Backpack Bag with Ntegrated RGB Light Strips 530X340X260mm
191.49 USD
208.14 USD
Free shipping
8%
off
Diatone LS5 Frame Parts Upper/Bottom Plate/Side Plate/Middle Plate/Arm Plate
3.7 USD
4.02 USD
2.0 USD
8%
off
Speedy Bee 5.8GHz Antenna 2.0Dbi RHCP SMA/UFL/MMCX FPV Antenna for Racing Drone
11.74 USD
12.76 USD
2.0 USD
8%
off
Diatone Mamba Micro to Type-C Tuning Extension Cable 100mm For RC FPV Drone
5.73 USD
6.23 USD
2.0 USD
8%
off
HawkEye Four Eyes 4CHl 5.8G Receiver with TV Dual Way Output for DIY Quadcopter
282.95 USD
307.55 USD
Free shipping
8%
off
Happymodel 2.4g ExpressLRS ELRS Nano TX module ES24TX Slim for X-lite Tango2
ES24TX Slim 2.4G ExpresLRS Nano transmitter module tuner module X-lite Tango2 compatible
This Slim TX module is designed by Happymodel and based on the open source- ExpressLRS which is a very popular low latency and high re-flashed rate RF module for RC Airplane and FPV Racing drone. Its main hardware architecture is ESP32, ESP8285 and SX1280 RF chip. The ES24TX Slim module is a complete solution which is already pre-load the Expresslrs firmware and it’s plug and play for Frsky X-lite/X-lite pro/X9 Lite , TBS Tango2.
This Slim module comes with an aluminum alloy shell and is equipped with a cooling fan that automatically works when the module is working at 250mw.
Features:
Open source ExpressLRS
Long range, low latency and High re-flashed Rates
Supports up to 250mw RF power
Telemetry data transmission supported
Cooling fan provide
CNC aluminum protective shell
Specifications:
Regulatory Domain: ISM2400
MCU:ESP32(main),ESP8285(aux,as espbackpack)
RF chip:SX1280IMLTRT
Lite Frsky 8pin socket
Frequency Range: 2400 MHz to 2500 MHz
Maximum receive refresh rate: 500Hz
Minimum receiver refresh rate: 25Hz
RF Output Power: 10dBm~24dBm
Power supply voltage: 5v~10v
Weight: 48gram(with antenna and case）
Dimension: 60mm*30mm*20mm(With CNC case)
Antenna gain:1.87dBi
Package include:
ES24TX Slim TX module *1
24TX80 antenna *1
CNC Aluminum alloy case *1
Cooling Fan *1
LED board *1
Antenna adapter cable *1
Since the official ExpressLRS perfect program has not been released yet, our pre-installed program is a beta version, because there are too many types of beta version programs , You can download the firmware from our website or update by ExpressLRS configurator, and then update the firmware via connect the Wifi hot spot of the “ExpressLRS TX Module”, visit "10.0.0.1" by browser (password:expresslrs)
Firmware target:
Happymodel_ES24TX_ESP32_SX1280_E28_aec8ad82 match with EP1/EP2 RX
Firmware RC3 to match with ELRSF4 2G4 Flight controller board38866e match with ELRSF4 2G4
Notice:
The painting defects of CNC aluminum alloy casing are acceptable.
Please make sure to fix the plastic burrs of the socket interface before installing the module PCB.
When installing the LED board, please put it in place and put the wire into the corresponding slot to avoid interference with the installation of the cooling fan.